ivo.tec water+
Advanced technology and good form for modern living needs
Pellet stove with integrated water heat exchanger and very high efficiency (over 90%). 80% (S5: 90%) of the heat is fed into the heating circuit from a buffer storage system. Stored energy can be released from the buffer at any time and as needed. 20% of the nominal thermal output is radiated directly into the room. This means the stove can also be used in low-energy or passive houses.
The combustion chamber of a room-sealed pellet stove is completely airtight. In addition, room-sealed wodtke pellet stoves have a tightly closing (TYPE CC) firebox door. In a pellet stove that operates independently of the ambient air, the oxygen required is not supplied from the room in which it is installed, but via a combustion air supply connected to the outside or via an exhaust air chimney. A pellet stove tested for room-sealed operation in accordance with EN 16510 is therefore ideal for installation in very airtight buildings, such as low-energy or passive houses, in combination with a controlled residential ventilation/ventilation system.
Of course, all room-sealed pellet stoves and wood-burning stoves from wodtke can also be operated in a room-sealed manner, i.e., without an external air supply.
In any case, you should involve your local district chimney sweep (building inspector for combustion appliances) at an early stage of your planning. Information on whether your desired stove has been tested and approved for room-sealed operation according to EN 16510 can be found in the operating manual of the respective model.
- Available in 2 attractive colours
- Patented, extra safe combustion technology
- Microprocessor controlled fuel and combustion air quantities are adjusted perfectly to one another for the most effective combustion performance available
- Up to 57 h run time on a single filling
- Reserve container with innovative sliding lid on rollers and folding cover for approx. 40kg pellets
- Extremely high water percentage, up to approx. 90% of power from water at nominal thermal output
- Integrated flow temperature limitation (85°C)
- ivo.tower (optional), attachable pellet reserve container extends run time up to 190 h
- Stainless steel burner pot and swivelling grate
- Automatic burner pot cleaning with swivelling grate and large ash pan, cleaning required only after approx. 500 kg pellet usage
- Comfortable operation on the stove or through an external thermostat
- Very quiet operation
- Connection for external pellet loader (optional)
- 8 rollers for easy handling and adjusting feet for stable base and height adjustment
- Glass door visibility screen for reduced thermal radiation - standard accessory
Adjustment range 3 – 8 kW, 3 – 9 kW oder 3 – 13 kW
Spatial heating capacity: min. 60 m² / max. 260 m²
Rear flue tube connection Ø 100 mm
Width 58 cm, depth 65 cm, height 122 cm
with ivo.tower width 109 cm, depth 83 cm, height 140 cm
- 2nd Level of 1st BImSchV (German Federal Emission Protection Ordinance) fulfilled
- Nominal thermal output 8, 9 or 13 kW
- Spatial heating capacity of 60 m² to 260 m² (min./max. output) at a demand of 50 Watt/m²
- Fuel: wood pellets with ash content < 0,7%
- CO content in exhaust air < 0,02 %-Vol.
- 8kW
Exhaust gas temperature 60°C - 62°C
Exhaust gas mass flow 3,8 - 5,3 g/s
Required supply pressure (chimney draught) 12 PA
- 9kW
Exhaust gas temperature 60°C - 90°C
Exhaust gas mass flow 3,8 - 7,5 g/s
Required supply pressure (chimney draught) 12 PA
- 13kW
Exhaust gas temperature 60°C - 105°C
Exhaust gas mass flow 3,8 - 9,7 g/s
Required supply pressure (chimney draught) 12 PA
- Multiple exploitation possible with safety device
- Tested in accordance with EN 16510-2-6
- Room air-independent operation possible (Type CC, tested and approved according to EN 16510)
- Reserve container for approx. 40 kg pellets
- E-power intake < 50 W
- Short-term E-ignition 250 W
- Weight 299-307 kg
