New Look F9
With wodtke HiClean-Filter® technology and three viewing windows
The combustion chamber of a room-sealed stove is completely airtight. In addition, room-sealed wodtke stoves are equipped with a self-closing (TYPE CA) firebox door that seals automatically. The required combustion air for a room-sealed stove is not drawn from the installation room but is instead supplied via an external combustion air supply connection or through a concentric flue system (air/flue gas chimney).
A stove tested and certified for room-sealed operation in accordance with EN 16510 is therefore ideally suited for installation in highly airtight buildings, such as low-energy or passive houses, and for use in combination with a mechanical ventilation system or controlled residential ventilation.
Of course, all room-sealed wood-burning and pellet stoves from wodtke can also be operated in a room-air-dependent mode, i.e., without an external air supply.
In any case, you should involve your local district chimney sweep (building inspector for combustion appliances) at an early stage of your planning. Information on whether your desired stove has been tested and approved for room-sealed operation according to EN 16510 can be found in the operating manual of the respective model.
wodtke HiClean-Filter technology works without any complex additional components. With innovative filter materials and a well-thought-out air supply, emissions and fuel consumption are effectively reduced, while the stove's efficiency and heat exchange are increased significantly.
The depth filter made of ceramic foam and positioned above the combustion chamber retains the particles generated primarily during the initial phase of combustion. After the ignition temperature is exceeded, these are burnt, leaving the filter clear after each combustion phase. The filter also retains combustion gases for a longer period of time at a significantly higher temperature in the combustion chamber, leading to noticeably better combustion.
wodtke Air Control regulates the combustion air supply for an optimal combustion process. The system requires no valves or gates. This significantly increases operating comfort and eliminates user error. All users need to do is regularly refill the fuel supply.
Air Control thermal regulation is based on a hydraulically activated control valve connected to a temperature sensor through a capillary system. Thanks to Air Control, the right quantity of combustion air is delivered to the right area of the combustion chamber. At the beginning, when the system is still cold, the fire needs a large quantity of primary air in order to quickly start a clean combustion process. This combustion air must be fed through the grate from below. As the system heats up, the thermal oil in the temperature sensor expands, slowly closing the control valve. This process automatically closes the primary air duct. Afterwards, the combustion air is fed downwards to the flame as secondary air and as an 'air curtain' for the window. This AWS air wash system effectively delays soiling of the viewing window.
- Three viewing windows provide a generous view of the fire
- HiClean-filter easily accessible through inspection door
- Door handle stays cool during operation
- Door handle with Swarovski® crystals
- Storage area in base
- Secondary air preheating for especially low-emission combustion
- AWS window air wash system
- High-quality, double-wall steel construction
- Combustion chamber cladding with proven Vermiculite
- Long-lasting fire grate made of solid cast iron
- Ash pan for easy ash removal
- Flue tube connection at top or rear possible
Adjustment range 3 - 7 kW
Spatial heating capacity: min. 47 m³ / max. 116 m³
Burns wood
Width 46 cm, depth 46 cm, hight 128 cm
- 2nd level of 1st BlmSchV (Federal Emission Protection Ordinance) fulfilled
- Nominal thermal output 6 kW
- Spatial heating capacity of 47 m³ to 116 m³in accordance with DIN 18893
- Burns wood
- CO content in exhaust air < 0.12 % vol.
- Exhaust gas temperature 275°C (F) 290°C (U)
- Exhaust gas mass flow 6 g/s (F) 5,5 g/s (U)
- Required supply pressure (chimney draught) 12 PA
- Several stoves may be connected to one chimney
- Tested in accordance with EN 16510-2-1
- Room air-independent operation possible (Type CA, tested and approved according to EN 16510)
- Flue tube connection at top or rear Ø 150 mm
- Connection for combustion air supply Ø 100 mm
- Weight 190 kg
